http://www.777slotsclub.com/slots-nuts-com/
Paracord is an impressive string used to knit! It's tough, lightweight, washable and virtually indestructible! This tutorial will show how a "manly" collar for your dog using the node sawtooth or zigzag.
Supplies and tools needed
You will need some basic tools to do this project. A C-clamp, hemostats, scissors, a lighter, a flexible tape, a 3 / 4 "D-ring pressure Plastic and paracord.
Preparation Paracord
Preshrink paracord is needed before use. For preshrink the paracord, soak in hot water for 5 minutes, then hang the paracord dry.To to determine how much you need for your project, you always take your dog's neck and multiply by four. A measure of the sample collar is 18 "X 4 = 72". Therefore, you have two lines of paracord that each 72 "long.
STEP 1 – Put the chain and ring D in the snap
Fold the rope in half and run each addition until the end of the single slit. Now run the D-ring through the ropes and close to the component snap. Now run the ends of the rope through the loop of string protruding from the bottom of the complement. Pull the rope tight
STEP 2 – Snap fastening
Connect the snap down on a stable surface like a table. This Snap maintained regularly and you will be able to put stress on the strings when you are connecting.
Step 3 – The first node
To make the switch node will be alternating knot half hitch knots. Take the first set of strings, it takes behind the second set String and pass through the loop you just created. Tighten the nodes. Do not over tighten your job or start turning node.
STEP 4 – the second knot
You now have the second set of string and tie a knot and a half in the opposite direction. To celebrate, take the first series of string and a knot in the same direction as it did with the node 1. Keep the knot in the opposite direction until the knotted rope, two inches below your final measurement. Do not forget to take into account the complement of the time to take his measure. Stop link to 16 ".
STEP 5 – Connect the cables in bulk to supplement
Run the child or the final two slots in the marrow and leave an inch of bone from the end of the knot work.
Step 6 – Finish Cable Ends Part 1
Take a line of each set, then run forward and the top of the loop you created in the back of the ropes that collar.Lay knot against the back of the neck. Tighten the knot insofar as it goes.
STEP 7 – The Ends of the cable finishing the second part
Search the number 1 cable passes under a series of 2 cable. Passage of the clip in the series 2 cable, pull the rope of the Assembly from 1 to hemostatic and escape. Repeat with the second set of strings. Make This "tie back" a again. Now stretch your neck with your hands and cut the strings as close as possible to the neck.
STEP 8 – Merging strings
* NOTE * hot plastic is dangerous and can burn very badly! Be careful when melting the cable ends!
Take your lighter and place the flame closer can be cut the strings. You really need to get nice and warm. When the cable ends brown and bubbly, take the flat side of your scissors and press on warming cord in the neck. You may have another step with the lighter if the strings are not properly combined.
Once cooled the molten ends of the neck, can put on your dog.
Karen Friesecke is the author of Bloggie Stylish a new blog dedicated to recipes and free projects for dogs. Please visit Seesaw Knot Dog Collar Tutorial to see this tutorial, complete with pictures.
|
|
Tripp Lite 42U Rack Enclosure Shallow Depth with Doors and Sides 3000lb Capacity – SR42UBSD (Black) $1,137.03 42U Rack Enc Shallow Depth… |
|
|
Camco 57363 Leveling Scissor Jack Socket $4.05 Camco Scissor Jack Drill Adapter… a time – saver! Lower and raise your scissor jacks in record time! This drill adapter fits 3/8″ or 1/2″ power drills so you don’t have to raise that jack manually! Works with all 3/4″ hex drive jacks. Scoop this Adapter up today! Camco Scissor Jack Drill Adapter… |
|
|
KD Tools 41660 Spindle Nut Service Kit $60.50 ul> 1/2 in. drive sockets used for most 4WD SUV and light truck axle locknut applications Off corner loading on drive pins for increased strength Use with a torque wrench, ratchet, or breaker bar Made of chrome vanadium steel Packaged in a blow molded case with laminated instruction cards or stickers integrated into case design for handy reference of application information Applications: 4-Lug 4… |
|
|
AP Products 014-122081 6 Slot Spindle Nut $4.95 … |
|
|
Festool 491594 Quick Clamp For MFT And Guide Rail System, 6 5/8 (168mm) $36.00 Type FS-HZ 160. Easy lock and release for use with multifunction table and guide rails. Clamping capacity approximately 6-5/8″. Contains 1 clamp. Compatible with Festool MFT/3 Multifunction Table, MFT/3-Kapex Multifunction Table, Kapex KS 120 Sliding Compound Miter Saw, MFT/3 Multifunction Table Basic. Festool products can only be sold in the 50 states…. |